GeekVape Wenax H1 Replacement Pods
Geek Vape Wenax H1 Replacement Pods
Geekvape Wenax H1 Replacement Pods are the genuine refill cartridges for the Wenax H1 pod system, sold in packs of three with the mesh coil already integrated - there is no separate coil head to install. Each pod holds 2.5mL and uses a 5-layer internal structure designed to stop leaking and droplets, which is the part that separates these from the generic pods that seep into your pocket after a week. Refilling goes through a side-fill port sealed with a silicone stopper, so you never have to pull the mouthpiece off, and the magnetic connection snaps the pod in and out in seconds. Two builds are available: the 0.7ohm runs at 16-19W for a looser draw with fuller vapor and works with 50/50 freebase or salts, and the 1.4ohm runs at 8-10W for a tight MTL pull that suits higher-strength nic salts and stretches battery life noticeably further. Mesh construction increases the heated surface area, which is what keeps flavor bold and extends how long each pod lasts before it starts to taste tired.
WARNING: This product is intended for use with nicotine-containing e-liquid. Nicotine is an addictive chemical. For adults 21+ only.
Key Features
- 3-Pack - three pods per pack, coil pre-installed
- Two Resistance Options - 0.7ohm and 1.4ohm
- 2.5mL Refillable Capacity
- Integrated Mesh Coil - richer flavor and longer pod life
- 5-Layer Leakproof Structure - built to stop seeping and droplets
- Side-Fill System - silicone-stoppered port, no disassembly
- Magnetic Connection - snaps on and off in seconds
- MTL Optimized - both resistances suit mouth-to-lung vaping
- Genuine Geekvape - designed specifically for the Wenax H1
Specification Table
| Brand | Geekvape |
|---|---|
| Product | Wenax H1 Replacement Pods (Pods Only) |
| Pack Count | 3 Pods Per Pack |
| Pod Capacity | 2.5mL |
| Coil Resistance | 0.7ohm (16-19W) / 1.4ohm (8-10W) |
| Coil Type | Integrated Mesh (Non-Replaceable) |
| Vaping Style | MTL and Restricted DTL |
| Fill System | Side Fill, Silicone Stopper |
| Leak Protection | 5-Layer Internal Structure |
| Connection | Magnetic |
| Compatibility | Geekvape Wenax H1 Pod System |
| Refillable | Yes |
| Ships Filled | No (Empty Pods) |
What's Included
- 3 x Geekvape Wenax H1 Replacement Pods
Choosing Your Resistance
- 0.7ohm (16-19W) - looser draw with fuller vapor and a warmer hit. Works with 50/50 freebase or nic salts at moderate strength
- 1.4ohm (8-10W) - tight MTL draw closest to a cigarette, cooler and far easier on battery life. Built for higher-strength nic salts
FAQ
Q: Which device do these pods fit?
A: The Geekvape Wenax H1 Pod System. These are proprietary to the H1 and do not fit other Wenax models such as the Wenax Q or Wenax U, which use different cartridge platforms.
Q: What is the difference between 0.7ohm and 1.4ohm?
A: The 0.7ohm runs at 16-19W with a looser draw and more vapor. The 1.4ohm runs at 8-10W for a tighter cigarette-like pull, and because it draws roughly half the power, it gets noticeably more vaping out of a single charge.
Q: How many pods come in a pack?
A: Three. All three are the same resistance - choose which one when ordering.
Q: Do the pods come filled with e-liquid?
A: No. These ship empty and are refillable. Fill through the side port with the e-liquid or nic salt of your choice.
Q: Do I need to prime a new pod?
A: Yes. Fill it and let it sit for around five minutes before the first vape so the cotton fully saturates. Skipping this step is the most common cause of a burnt taste on a brand new pod.
Q: Can I replace just the coil?
A: No. The coil is built into the pod, so you replace the whole cartridge rather than dealing with coil heads and tools.
Q: What e-liquid works best?
A: 50/50 blends and nic salts. These are low-wattage MTL pods, so high-VG liquid is too thick to wick reliably and will cause dry hits.
