Uwell VALYRIAN III Replacement Tank

Uwell VALYRIAN III Replacement Tank

The Uwell VALYRIAN III is the third generation of Uwell’s flagship sub-ohm tank, built in stainless steel and Pyrex glass with a 6mL capacity in a 30mm body — noticeably slimmer than the 32mm Valyrian IV, so it sits flush on more mods. A flip-cap top fill opens with one press of a button and feeds dual fill ports, and a dual-slot bottom airflow ring tunes the draw. It ships with two coils — a 0.32Ω UN2 (80–85W) and a 0.14Ω UN2-2 (80–90W) — and is cross-compatible with Valyrian II coils and V-Coils, so existing coil stock carries straight over. Pro-FOCS flavor technology and progressive self-cleaning keep condensate out of the airflow path.

Key Features

• 6mL e-liquid capacity in a 30mm body — slimmer than the Valyrian IV
• Flip-cap top fill — press the button, the cap swings fully open, dual fill ports
• Dual-slot bottom airflow control ring — restricted through wide-open direct lung
• 0.32Ω UN2 (SS316L) coil included, rated 80–85W
• 0.14Ω UN2-2 (FeCrAl) coil included, rated 80–90W
• Cross-compatible with Valyrian II coils and V-Coils — 0.15Ω (100–120W) and 0.16Ω UN2-3 (90–100W) both fit
• Pro-FOCS flavor technology for sharper, denser flavor delivery
• Progressive self-cleaning design — condensate is channeled away from the airflow path
• Threaded coil installation — screw-in, not push-fit, for a secure seal
• Stainless steel body with Pyrex glass
• Threaded 510 connection — fits virtually any sub-ohm box mod
• Spare bubble glass and O-ring pack included
• 5 finishes — Black, Silver, Gunmetal, Blue, Iridescent

Specification Table

What’s Included

• 1 × Uwell VALYRIAN III Tank
• 1 × UN2 Coil 0.32Ω (pre-installed)
• 1 × UN2-2 Coil 0.14Ω
• 1 × Bubble Glass Tube (spare)
• 1 × O-Ring Pack
• 1 × User Manual

FAQ

Q: Will my Valyrian II coils or V-Coils work in this tank?

A: Yes. The Valyrian III accepts Valyrian II coils — including the 0.15Ω (100–120W) and 0.16Ω UN2-3 (90–100W) — as well as V-Coils. Any Valyrian-series coil you already own will screw straight in.

Q: What wattage should I run each coil at?

A: The 0.32Ω UN2 is rated 80–85W and the 0.14Ω UN2-2 80–90W. Start at the low end, take a few short priming puffs, then work up — jumping straight to the ceiling on a dry coil is the fastest way to burn the cotton.

Q: How is this different from the Valyrian IV?

A: The IV is larger — 8.5mL and 32mm — and ships with V-Coils (0.18Ω / 0.35Ω). The III holds 6mL in a 30mm body, which sits flush on more mods, and ships with UN2 coils at a lower wattage band. Coils interchange between them, so the choice is capacity and width versus footprint.

Q: Will it fit my mod?

A: It uses a standard threaded 510 connection, so it fits almost any sub-ohm box mod. At 30mm it will still overhang narrow mods — check your device is at least 28–30mm across for a flush fit. Do not use it on a hybrid-style device.

Q: What e-liquid should I use?

A: High-VG freebase e-liquid, 70VG/30PG or higher, in low nicotine strengths — typically 0–6mg. Do not use high-strength nicotine salts in a sub-ohm tank at 80W+.

Q: How do I fill it?

A: Press the button on the top cap, the flip cap swings fully open to expose the dual fill ports, fill to just below the top of the chimney, then close the cap. Let a freshly installed coil sit 5–10 minutes before the first draw.