Vaporesso Target PM30 Replacement Pods
Vaporesso Target PM30 Replacement Pods
The Vaporesso Target PM30 Replacement Pods are official empty cartridges for the Target PM30 Pod Mod Kit, sold two to a pack. Each pod holds 3.5mL of e-liquid and uses Vaporesso's PTF (Push To Fill) system — a sliding top cap with a press-to-seal plug that locks the fill port shut rather than relying on a friction-fit stopper. It's a more secure closure than most pods in this class, and the reason these hold up well against leaking in a pocket or bag. The pods take the Vaporesso GTX coil platform, most commonly the 0.6Ω GTX mesh at 20–30W for a looser, more vapor-forward draw and the 1.2Ω GTX regular at 8–12W for a tight mouth-to-lung hit. Coils install press-fit — push straight into the base, no threading, no tools — and a magnetic connection seats the pod firmly in the device while keeping the contacts clean.
Coil Options (Sold Separately)
| Coil | Wattage | Draw | Pair With |
|---|---|---|---|
| GTX 0.6Ω Mesh | 20–30W | Restricted direct-lung | Low-nicotine freebase (3–6mg) |
| GTX 1.2Ω Regular | 8–12W | Tight mouth-to-lung | Nic salts or high-nicotine e-liquid |
Other GTX coils rated within the PM30's 8–25W output range also fit.
Key Features
- Pack of 2 Replacement Pods — official Vaporesso
- 3.5mL E-Liquid Capacity per pod
- Empty Pods — no coil pre-installed, choose your own resistance
- PTF (Push To Fill) Sliding Top-Fill System — secure, leak-resistant seal
- Vaporesso GTX Coil Platform Compatible
- Press-Fit Coil Installation — quick, tool-free swaps
- Magnetic Pod Connection
- Ergonomic Mouthpiece
- Refillable Design
Specification Table
| Spec | Details |
|---|---|
| Brand | Vaporesso |
| Product | Target PM30 Replacement Pods |
| Quantity | 2 per pack |
| Capacity | 3.5mL |
| Filling | Sliding Top Fill — PTF (Push To Fill) Port |
| Coil Installation | Press-Fit |
| Connection | Magnetic |
| Coil Compatibility | Vaporesso GTX Coil Series (0.6Ω 20–30W / 1.2Ω 8–12W) |
| Device Compatibility | Vaporesso Target PM30 Pod Mod Kit |
| Coils Included | No — sold separately |
What's Included
- 2 × Vaporesso Target PM30 Replacement Pods (Empty, No Coils)
FAQ
Q: Do these pods come with coils?
A: No. They ship empty with no coil installed. You'll need Vaporesso GTX coils, sold separately. This lets you pick the resistance that matches your draw style rather than being locked to one.
Q: Which coil should I pick?
A: Match it to your e-liquid. Use the 1.2Ω at 8–12W for a tight, cigarette-like draw with nic salts or high-nicotine e-liquid. Use the 0.6Ω mesh at 20–30W for a looser, more vapor-forward draw with low-nicotine freebase. If you're switching from cigarettes, start with the 1.2Ω.
Q: What is PTF?
A: Push To Fill. The top cap slides open to expose the fill port, and a press-in plug seals it shut afterwards. It's a firmer closure than the silicone stoppers used on most pods, which is why these tend to stay clean in a pocket.
Q: Will any GTX coil fit?
A: Any GTX coil that works within the PM30's 8–25W output range. Higher-wattage GTX coils will physically fit but won't get enough power to perform properly, so avoid them.
Q: Which devices do these fit?
A: The Vaporesso Target PM30 Pod Mod Kit only. They won't fit the Target PM40, Target PM80, or any of the Luxe and XROS pod systems — each uses its own pod, despite sharing the GTX coil platform across the range.
Q: How do I install a coil?
A: Push the GTX coil into the base of the pod until it seats — it's a press fit, don't twist. Then prime it: drip e-liquid onto the exposed cotton, fill the pod, and let it stand ten minutes before your first puff. Skipping this is the main cause of burnt coils.
Q: How often should I replace the pod itself?
A: Coils wear out well before pods do. Most vapers change the coil every one to two weeks and the pod every few months, or sooner if the plastic clouds up, the fill plug stops sealing properly, or flavor stays flat after fitting a fresh coil.
Q: Why is my pod leaking?
A: Usually a coil that isn't fully seated, or a fill plug that isn't pressed all the way home — check both first. Thin, high-PG e-liquid can also seep past a 0.6Ω mesh coil; a thicker blend helps.
